APC8621A Non-intelligent PCI Bus Carrier, Half-Length
APC8621A: Non-intelligent PCI Bus Carrier, Half-Length
Product short description:
- Nonintelligent PCI bus carrier
- Holds three IP modules
- Plug-and-play carrier configuration and interrupt support
- Two interrupt channels per IP module
- Supervisory circuit reset generation
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
Description
APC8621A: Non-intelligent PCI Bus Carrier, Half-Length Description
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
Three IP module slots give you the freedom to mix a variety of I/O functions (A/D, D/A, digital in, digital out, serial I/O, etc.) on a single board. Or, combine modules of the same type for dozens of channels on a single card. Either way, the APC8621A saves your precious card slots and reduces your costs.
Select I/O modules from Acromag’s offering of more than forty models or use any third-party IP mezzanine ANSI/VITA 4 modules.
The APC8621A is a drop-in replacement for the APC8621, please see the known differences document below for more information.
APC8621A: Non-intelligent PCI Bus Carrier, Half-Length Description Performance Specifications
IP Module Compliance (ANSI/VITA 4)
Meets or exceeds all written IP specifications per ANSI/VITA 4-1995 for 8MHz or 32MHz operation. Supports Type I and Type II ID space formats.
Electrical/mechanical interface: Supports three single-size IP modules (A-C), or one double and one single-size IP module. 32-bit IP modules are not supported.
IP module I/O space, ID space, INT, and MEM space supported.
IP module I/O space: 16 and 8-bit; supports 128 byte values per IP module.
IP module ID space: 16 and 8-bit; Supports Type I 32 bytes per IP (consecutive even byte addresses) and Type II 32 words per IP via D16 data transfers.
IP module memory space: 16 and 8-bit; supports up to 8M bytes of memory space per IP module.
Interrupts: Supports two interrupt requests per IP and interrupt acknowledge cycles via access to IP INT space.
PCI Bus Compliance
This device meets or exceeds all written PCI local bus specifications per rev. 2.2 dated December 1998.
System base address: This board operates in PCI memory space. It requires 1K of memory space for mapping the carrier controls, and IP module ID, INT, and I/O space. An optional 64MB of PCI memory space is required to use IP module memory space.
Data transfer bus: Slave with 32, 16, and 8-bit data transfer operation. 32-bit read or write accesses implemented as two 16-bit transfers to IP modules.
Interrupts (PCI bus INTA# interrupt signal): Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space.
Environmental
Operating temperature: 0 to 70°C.
Storage temperature: -55 to 100°C.
Relative humidity: 5-95% non-condensing.
Power: 3.3 Volts (±10%): 130mA, typical; 50mA max. 5 Volts (±5%): 30mA, typical; 50mA, max. ±12 Volts provided to each IP module.
MTBF: 413,003 hrs. at 25°C, MIL-HDBK-217F, notice 2.
Physical
Physical configuration: PCI universal card (3.3V or 5V).
Length: 6.600 inches. (167.64 mm).
Height: 4.200 inches. (106.68 mm).
Board thickness: 0.062 inches. (1.59 mm).
Maximum component height: 0.380 in. (9.65 mm).
Max. height under IP modules: 0.180 in. (4.57 mm).
Connectors: A-C (carrier field I/O): 50-pin male header.